How to fill the space between the dresser and the wall: a detailed guide (2023)

If you're a fan of a clean and polished look, especially in bathrooms, you might not like that annoying gap between the vanity and the wall. although it can only be one2 inch spacing, it's still noticeable from certain angles.

can be a bit challengingfind the right methodto address this issue in a way that is functional, durable, and yet aesthetically pleasing.

Today we will talk about the best wayFill in the gap between the vanity and the wallthat is durable, seamless and in tune with your interior design.

This way you avoid a gap between the vanity and the wall

When it comes to any topic, especially ininterior design, It's getting betterbe preventedthan to "treat" it later. The same applies toGap between vanity and bathroom wall, which is a very common problem.

Of course, this step only makes sense for those of you who are in the process of planning where and where you want your vanity to goHow are you going to attach it to the wall?🇧🇷 Our tips and tricks for fixing the already done gap will be discussed a little later.

Needless to say, it might be helpful to read this part briefly as well so that you are awarepossible errors and problemsthe next time you install a powder room in your home.

Öso calledfloating vanity, or wall hung vanity, is one of the most beautiful accessories you can add to your bathroom. It adds a touch of sophistication and class to any setting, while also being highly functional and easy to maintain.

Let's look at the crucial steps to do thisInstall your vanity successfullyon the wall and position it correctly so that little or no rework is required:

1. First of all it is necessaryPlan everything carefully🇧🇷 You want to decide where to put the vanity, measure everything (and repeat the measuring process to make sure your measurements are correct).
2. Use chalk for thisMark where your vanity will be placed.
3. Moverthe old sink
4. One of the most important factors is to check the wall and make sure it is completely straight. If not, you could end with alarge distance between dresser and wallwhich may be more difficult to complete later.
5. andWall requires some repair workPlease be sure to complete this step before installing the vanity as it is much easier to attach to a bare wall.
6. To thePrepare the wall for the powder room, You may scratch or grind the wall.
7. Make sure the wall is upcompletely dry and flatbefore assembling your vanity.
8. Put the dresser against the wallFollowing the marks you made earlier. Mark the positions of the screw holes.
9. Lay the dresser on its side andmake the holeswhere you made marks with an electric drill.
10. An important step in ensuring the stability and correct positioning of your vanity isAdding wall studs.
11. Place the cabinet under the sinkon the wall with screws.
12. you want to make sureVanity is stable, safe and happy with its location.
13. Put the sink in the closet, ensureperfectly adjustedand connected to the drain andInstallation🇧🇷 Also make sure the hoses are sealed to prevent leaks.
14. The last step is to use caulk to make sure there aren't anylarge distance between sink and wall🇧🇷 You also want to fill in the space between the wall and the dresser. This also protects the wall and washbasin from water.

This is how you fill in the space between the dresser and the wall

If you have ever found yourself in a difficult situation and are looking for a castdistance between washbasin and wall,or theGap between vanity and side panel, this is also possible after the washbasin has been installed.

It's important to address the fact that if yourThe vanity does not touch the walls, it's not a critical issue as long as it doesn't cause other issues. Some vanity units are simply designed to leave a certain amount of space between the cupboard and the wall.

However, there's always the aesthetic factor, and you might want to bridge the gap regardless of functionality. This gap can alsocreate problemslike water stains or even mold behind the vanity which is definitely a sign of the crowning glory (after cleaning).

Below are the steps to do thisFill in the gap between the vanity and the wallbased on the size of the gap itself.

Tape for sealing bathrooms (small spaces)

If you are dealing with a small space, one of the best solutions you can use is to fill it upsealing tape for bathroom🇧🇷 This type of tape is waterproof and should last a long time. Once worn out, you can simply replace it with a new part.

1. Before attaching the tape it is necessaryclean the area welland make sure it is completely dry. If you apply the tape to a wet area, the adhesive will not stick and the tape will continue to slide until it falls off completely.
2. Make sure after attaching the tapesqueeze it hard, so the glue can stick in place. Pressing it against the surface will lock it in place. Allow the glue to dry completely before using the sink.

caulking (small gaps)

Like the tapePutty is extremely easy to useand is a convenient solution for use in the stucco process for smaller spaces. If we were to compare the two we would have to say that caulk is a slightly more durable material and you might find it easier on the eyes too.

1. Prepare areaClean it well and make sure it is dry before caulking.
2. Cover the walls with masking tapeso you don't put putty on them. This will also help you get a straight line.
3. fill the gapwith the sealant and allow it to dry completely before using the sink.
4. To usetransparent sealif you don't want it to appear.

Sealing with support rod (medium ranges)

If the gap is a little bigger, just filling it with putty won't solve the problem. You will need a littlemore support and securitythat you can easily getAdding a support bar.

1. Prepare areaClean it and make sure it is dry before you start work.
2. Place the support barin the space between the closet and the wall.
3. add caulkingto fill the gap but also to cover and secure the support bar.
4. You canchoose puttyin your wall/tile color or simply use clear caulk so the color doesn't conflict with your bathroom design.

Upstand (large areas)

A thick backsplash or drywall is not only a convenient and highly functional solution to this problem, it can be onemodern addition to your bathroom design, and a nice touch of color and/or texture for the color scheme.

This is an excellent option if you're having trouble with the water reaching youbehind the wallwhen using the sink or just looking for a stylish optionmake the vanity "disappear" in the wall, without significant gaps.

A backsplash comes in many sizes, designs and colors for you to choose from.which you can combine with the design of your bathroom, and the size of the area you want to cover.

1. clean the areaand make sure it is completely dry and free of dust and particles before beginning the process.
2. Use a level and tape measureto measure the area where you are applying the backsplash. Be sure to create guidelines with chalk or pins.
3. Apply a layertile gluewith a palette.
4. apply the tileson the sticky layer, be sure to secure each tile by gently pressing and twisting. Also, make sure the tile is properly laid before allowing the adhesive to dry.
5. use spacers, which will help you place the tiles correctly and make sure they line up. Also, these spacers prevent the tiles from moving up and down.
6. Be sure to remove the side spacer with each new tile, howeverthe lower and upper spacersit should remain until you complete the entire line.
7. Repeat all stepsuntil you have placed all the pieces and completed the entire backsplash. Check the placement of all tiles and make corrections before the glue starts to dry.
8. Leave the sticker fordry overnightand avoid using water in the area to keep the tiles in place.
9. After the glue has dried, it's timeremove all spacers, as well as any pens you used to mark the area.
10. Prepare the mortarand spread onto the tiles, making sure to press the grout into all the gaps around the tiles.
11. Remove grout residueTile with a cleaning solution (mix one part regular vinegar to one part water).